PUR700+
Polyurea waterproofing

PUR700+ Spray-applied polyurea waterproofing

A two-component spray-applied polyurea elastomer forming a continuous, seamless waterproof membrane using specialist equipment, for concrete protection in building and infrastructure work.

聚脲建筑屋面

聚脲建筑屋面

Material & applications

Two-component elastic waterproofing

PUR700+ combines component A curing agent and component B special resin. Specialist two-component spray equipment produces a continuous, seamless elastic membrane. Rapid reaction, elongation, strength, abrasion and impact properties support the specified protective function.

Application fields

Applications include building structures, petrochemical and mining concrete tanks, dams, embankments, reservoirs, channels, wastewater and storage pools, swimming pools, water parks, roofs, basements, stadium stands, tunnels and bridge/rail structures. Chemical or immersion exposure requires identification of medium, concentration, temperature and duration. Water storage does not imply approval for drinking-water contact.

Polyurea reaction

Polyurea reaction

Polyurea reaction

Waterproofing applications

Waterproofing applications

Waterproofing applications

Sports-facility application

Sports-facility application

Sports-facility application

Technical data

Model-specific technical data

Physical-property specimens: laboratory spraying with GRACO H-xp3 and AP gun, 7-day room-temperature cure.
PropertyDataConditions
CompositionA: curing agent; B: PUR special resinTwo components
Mixed densityApprox. 1.04 g/cm³
Mixed weight solidsApprox. 98±1%
VOC100 g/LEN ISO11890-1
Flash point32°C
Theoretical consumption1.05 kg/m²1000 μm dry film; allow separately for site losses
Shelf life6 months, original sealed containers, cool and dryNot the working time after mixing
StorageDry, ventilated indoor storage 5–30°C; never below 5°C; above 25°C reduces shelf life6 months sealed
Heat resistance≤100°C
Watertightness0.4 MPa for 2 h, no penetration
Adhesion4 MPaActual adhesion depends on substrate and preparation
Gel time20 seconds
Tensile strength23 MPaLaboratory sprayed, 7 days at room temperature
Elongation at break510%Same specimen conditions
Tear strength77 N/mmSame specimen conditions
Low-temperature bending−40°C
Heat dimensional change≤0.4%
Water absorption≤2.5%
Abrasion13 [(750g/750r)/mg]
Impact resistance1.0 kg·m
Artificial weatheringGood after 2000 h
PackagingA: 220 kg; B: 200 kgPack weights are not the mixing ratio
ColourGrey or RAL colours

Application & system

Substrate and equipment

Use trained applicators and specialist high-temperature, high-pressure impingement-mixing equipment. Check primer thickness and compatibility; repair mechanical and corrosion damage. Coordinate joints, corners, penetrations and other details. Thinning is normally unnecessary; cleaning agent is KOALA thinnerEP100. Component A packaging is 220 kg and B is 200 kg: pack weights are not the mixing ratio.

Specimen conditions

Physical-property specimens were laboratory sprayed using a GRACO H-xp3 unit and AP gun, then cured for 7 days at room temperature. Actual substrate, equipment, thickness and site conditions influence results.

Application requirements

PropertyRequirement / data
PersonnelQualified contractor and trained applicators
Substrate temperature10–80°C
Relative humidityMaximum 85%; prevent condensation; temperature ≥3°C above dew point
SubstrateFollow primer instructions; measure old primer thickness, check system compatibility and repair damage
RecoatPrefer wet-on-wet; maximum 3 h
ThinningNormally unnecessary
CleaningKOALA thinnerEP100
Spray equipmentSpecified high-temperature, high-pressure impingement-mixing equipment

Drying & curing

Gel and recoat

Gel time approximately 20 seconds. Gelation is not full service-property development. Prefer wet-on-wet recoating, with a maximum interval of 3 hours. Define treatment for interrupted work, later recoating or special-media service.

Conditions & precautions

Conditions and model-specific data

Substrate temperature 10–80°C; RH ≤85%; application temperature at least 3°C above dew point. PUR700+ has approximately 98±1% weight solids, VOC 100 g/L and flash point 32°C. Heat resistance ≤100°C; low-temperature bending −40°C. Follow the SDS and the specific application process.

Storage

Store sealed in original containers for 6 months in dry, ventilated conditions at 5–30°C; never below 5°C. Temperatures above 25°C shorten storage life. Grey or agreed RAL colours are available.

Documents & specification support

Specify for your project.

Share the application, substrate, area and performance requirements to discuss a coordinated system.

Contact the factory